Pulsar Evolution Rack/Tower 2200/3000. MGE PowerServices. Software supplied Local and SNMP agents supervision software.
• Pulsar M 2200 RT 2U 2200 RT 3U 3000 RT 2U 3000 RT 3U 3000 RT 3U XL EXB RT 3U Installation and user manual - Page 1 34003641FR/AA. • - Page 2 34007776EN/AB. Playlist The Very Best Of Tyrese Rare. • Before installing Pulsar M, please read the booklet on the required safety instructions. Then follow the indications in this manual. Equazioni Alle Derivate Parziali Salsa Pdf To Word.
To discover the entire range of MGE UPS SYSTEMS products and the options available for the Pulsar M range, we invite you to visit our web site at www.mgeups.com or contact your MGE UPS SYSTEMS representative. • Introduction Pictograms Important instructions that must always be followed. Information, advice, help. Visual indication. Audio signal.
In the illustrations on the following pages, the symbols below are used: LED off LED on LED flashing - Page 4 34007776EN/AB. • Presentation Standard positions. 6 Tower position. 6 Rack position. 6 Rear panels. 7 Pulsar M 2200 / 3000. 7 Pulsar M EXB (optional battery module).
7 Control panel. 7 Installation Unpacking and contents check. 8 Installation in tower position.
9 Installation in rack position. • Tower position Rack position - Page 6 34007776EN/AB Dimensions (H x W x D) in mm Pulsar M 2200 RT 2U 440 x 86 x 640 Pulsar M 2200 RT 3U 440 x 131 x 490 Pulsar M 3000 RT 2U. • 1.2 Rear panels Pulsar M 2200 / 3000 Pulsar M EXB (optional battery module) 1.3 Control panel 1. Presentation (1) USB communication port (2) RS232 communication port (3) Connector for automatic recognition of an additional battery module (4) Slot for optional communication card (5) Connector for remote ON/OFF and RPO (Remote Power Off) control (6) Connector for additional battery module. Installation 2.1 Unpacking and contents check (30) Pulsar M 2200 or 3000 UPS (31) connection cable to AC-power source (32) 2 connection cables for the protected equipment (33) RS232 communications cable (34) USB communications cable (35) 2 systems to secure power plugs (36) Solution-Pac CD-ROM (37) Documentation Packing materials must be disposed of in compliance with all local regulations concerning waste. • It is advised to first install the battery module, then the power module above.
Follow steps 1 to 4 for module mounting on the rails. The rails and necessary hardware are supplied by MGE UPS SYSTEMS. Installation - Page 9. Installation 2.4 Communication ports Connection of RS232 or USB communication port (optional) The RS232 and USB communication ports cannot operate simultaneously. Installation of the communication cards (optional) - Page 6EN/AB 1 - Connect the RS232 (33) or USB (34) communication cable to the serial or USB port on the computer equipment.
• 2.5 Connections with a FlexPDU (Power Distribution Unit) module (optional) 2.6 Connections with a HotSwap MBP module (optional) The HotSwap MBP module makes it possible to service or even replace the UPS without affecting the connected loads (HotSwap function). Installation 1 - Connect the UPS socket (10) to the AC- power source using the cable (31) supplied. Installation HotSwap MBP-module operation UPS start-up with the HotSwap MBP module 1 - Check that the UPS is correctly connected to the HotSwap MBP module.
2 - Set switch (53) to the Normal position. 3 - Start the UPS by pressing the ON/OFF button (27) on the UPS control panel. The load is supplied by the UPS. • If UPS personalisation is desired, it is advised to enter the personalisation mode at this time. This mode may be entered using the buttons on the control panel or the Personal Solution-Pac software (Windows) included on the Solution-Pac CD-ROM provided by MGE UPS SYSTEMS.
3.2 Operation on battery power. • Pulsar has the choice of two remote control options. ◗ RPO: Remote Power Off allows a remote contact to be used to disconnect all the equipment connected to the UPS from the power supply. Restarting the UPS requires manual intervention. • Contact open: shut down of UPS Contact closed: start-up of UPS (UPS connected to the network and network energized) Note: local On/Off control via button (27) has priority over the remote control order.